ЗАО "ИНТЕРСИСТ" [тема: intp3a]

intp3a

Wed, 04 Aug 2021 18:25:34 +0500

intp3a Плата не в сервисе в форуме Конфигурирование.
Как оказалось был виноват PSAL, а [PowerOff] (IRQ #0 (0) - это инцидент на intip3, указывающий на это. Спасибо всем )
04.08.2021 18:25:34, santeri.

intp3a

Mon, 02 Aug 2021 08:16:43 +0500

intp3a Плата не в сервисе в форуме Конфигурирование.
Обе INTIP, которые в сервисе, включены в один и тот же Catalyst 2960, потом добавил INTIP3. Была долгая битва в попытке поднять порт на INTIP3, никак не могли договориться по скоростям, в итоге всем понравилось 1Gbit/s full duplex.
По дипам на обеих платах: X601 - boot from PLCC EPROM, JXK01 - series resistor, JXKK03 - relay open
В TC1842: если речь идет об этом:

The boards INTIP3 cannot be installed on coupler position for following references: - ACT14 :
o 3BA56006AAAA
o 3BA56006AAAB
- ACT28 :
o 3BA56007AAAA o 3BA56007AAAB
The references 3BA56006AAAC(01) and 3BA56007AAAC(01) were delivered from mid 1995.
The references 3BA56006AAAC(02) and 3BA56007AAAC(02) were delivered from sept 1995 (with mechanical improvement).

То наши p/n не попадают в эту категорию.
Интересен вот этот топик https://www.alcatelunleashed.com/viewtopic.php?t=27636&start=10, в котором vad писал:

If you have possibility for testing:
- on stand by AS - create empty database and load OPS files.
- create simple configuration - boards, IP addresses ...
- stop main AS and start stand-by (with test database)

You can check - all boards in services or not, IOP3 behaviour.
If with test database all board in services, or both IOP3 in services (all time) - you have problem with working database.

Попробую на чистой базе завести
02.08.2021 08:16:43, santeri.

intp3a

Sun, 01 Aug 2021 01:04:46 +0500

intp3a Плата не в сервисе в форуме Конфигурирование.
Рекомендую ознакомиться с TC1842 ed.2. "ACT COMPATIBILITY WITH INTIP3"
01.08.2021 01:04:46, Username.

intp3a

Sat, 31 Jul 2021 16:53:20 +0500

intp3a Плата не в сервисе в форуме Конфигурирование.
Проверьте ещё раз что у вас выставлено на dip
31.07.2021 16:53:20, error.

intp3a

Fri, 30 Jul 2021 21:07:43 +0500

intp3a Плата не в сервисе в форуме Конфигурирование.
можно еще посоветовать соединить LAN на самом простом коммутаторе, а-ля Д-линк (если стоит что-то мудрое типа циско - то там может быть мор на тему автонастроек порта, МТР и проч.) хотя довольно странно - у вас же INT-IP3 которые В - работают, как минимум одна и вероятно включена в тот же свич...
как некое подтверждение видно в вашем логе такое:
bonding: bond0: Warning: failed to get speed and duplex from eth1, assumed to be 100Mb/sec and Full.
30.07.2021 21:07:43, Dmitry Ryzhakov.

intp3a

Fri, 30 Jul 2021 16:20:46 +0500

intp3a Плата не в сервисе в форуме Конфигурирование.
Софт перезалил, перезагрузку кристалла сделал - без изменений. PSAL имеет значение для INTIP3B, а здесь INTIP3A
30.07.2021 16:20:46, santeri.

intp3a

Fri, 30 Jul 2021 05:58:39 +0500

intp3a Плата не в сервисе в форуме Конфигурирование.
Если перезагрузка кристала не поможет, можно попробовать перепрошить плату с помощью PC Installer. Временами это помогает.
30.07.2021 05:58:39, Владислав Хисамов.

intp3a

Fri, 30 Jul 2021 02:02:50 +0500

intp3a Плата не в сервисе в форуме Конфигурирование.
eth0/eth1 возможно, но если результата не принесёт стоит перезагрузить весь кристалл 2 (было такое же с заменой интофа который не хотел стартовать, перезагрузка кристалла помогла)
30.07.2021 02:02:50, error.

intp3a

Thu, 29 Jul 2021 23:31:53 +0500

intp3a Плата не в сервисе в форуме Конфигурирование.
еще в догонку. не копаясь в документации: а в релизах 10.1 уже есть плата INT-IP3 в режиме IOIP3... на память не помню, но хорошо бы уточнить... и судя по логам у вас активен eth1, доки вроде упорно советовали использовать для TFTP старта eth0 (другой коннектор)
29.07.2021 23:31:53, Dmitry Ryzhakov.

intp3a

Thu, 29 Jul 2021 23:28:47 +0500

intp3a Плата не в сервисе в форуме Конфигурирование.
хммм. две платы (предположим - заведомо исправные) ведут себя одинаково... а что там с PSAL на этом кристалле?
29.07.2021 23:28:47, Dmitry Ryzhakov.

intp3a

Thu, 29 Jul 2021 17:35:57 +0500

intp3a Плата не в сервисе в форуме Конфигурирование.
R10.1.1-j2.603-38-ru-c0
29.07.2021 17:35:57, santeri.

intp3a

Thu, 29 Jul 2021 17:32:08 +0500

intp3a Плата не в сервисе в форуме Конфигурирование.
INTIP3 работает с релиза 9.1. У вас какой?
29.07.2021 17:32:08, etc.

intp3a

Thu, 29 Jul 2021 13:34:15 +0500

intp3a Плата не в сервисе в форуме Конфигурирование.
Есть вторая intip3 и у нее поведение такое же. Плата вставляется полностью, поменяли слот и коннектор сзади платы, так же загрузка ходит по кругу
29.07.2021 13:34:15, santeri.

intp3a

Thu, 29 Jul 2021 13:22:37 +0500

intp3a Плата не в сервисе в форуме Конфигурирование.
Плата по какой-то причине получает сигнал [PowerOff] (IRQ #0 (0) received).
И выключается. Может, плохо вставлена?
29.07.2021 13:22:37, etc.

intp3a

Thu, 29 Jul 2021 11:46:58 +0500

intp3a Плата не в сервисе в форуме Конфигурирование.
config 2

+-------------------------------------------------------------------+
| Cr | cpl| cpl type | hw type | cpl state | coupler ID |
|----|----|------------|-----------|--------------|-----------------|
| 2 | 0 | NDDI2|---------- | REG NOT INIT | BAD PCMS CODE |
| 2 | 1 | eZ32|---------- | IN SERVICE | BAD PCMS CODE |
| 2 | 2 | GPA2|---------- | IN SERVICE | BAD PCMS CODE |
| 2 | 3 | eZ32|---------- | IN SERVICE | BAD PCMS CODE |
| 2 | 6 | INTIPB| INT-IP |ONLY OPS FILE | BAD PCMS CODE |
| 2 | 9 | GPA2|---------- | IN SERVICE | BAD PCMS CODE |
| 2 | 10 | eZ32|---------- | IN SERVICE | 3BA23265ABCB04 |
| 2 | 11 | NDDI2|---------- | REG NOT INIT | BAD PCMS CODE |
| 2 | 12 | eZ32|---------- | IN SERVICE | 3BA23265ABCB04 |
| 2 | 15 | DECT8|---------- | IN SERVICE | BAD PCMS CODE |
| 2 | 17 | eUA32|---------- | IN SERVICE | BAD PCMS CODE |
| 2 | 19 | NDDI2|---------- | REG NOT INIT | BAD PCMS CODE |
| 2 | 20 | INTIPB| INT-IP | IN SERVICE | BAD PCMS CODE |
| 2 | 22 | NDDI2|---------- | REG NOT INIT | BAD PCMS CODE |
| 2 | 23 | INTIP3A| INT-IP3 | REG NOT INIT | BAD PCMS CODE |
| 2 | 24 | INTIPA| INT-IP | IN SERVICE | BAD PCMS CODE |
| 2 | 26 | NPRAE|---------- | IN SERVICE | BAD PCMS CODE |
+-------------------------------------------------------------------+

--- Inter Crystal Topology ---

+-------------------------------------------------------------------------+
| CR | CPL Type Role Free/Tot Role Type CPL | CR |
|-------------------------------------------------------------------------|
|002 | 20 -INTIPB (MAIN ) --- 25/30 --- ( INT_A) INTIPA - 01 |019 |
29.07.2021 11:46:58, santeri.

intp3a

Thu, 29 Jul 2021 11:41:57 +0500

intp3a Плата не в сервисе в форуме Конфигурирование.
Добрый день! Пытаюсь ввести в сервис intip3, плата конфигурируется как intip3a, на станции прописаны ip-адрес платы, маска, шлюз, mac-адрес интерфейса. В инцидентах никакой информации на тему загрузки lanbpx.cfg, файл не грузит. Вот портянка с консоли платы:

Uncompressing Kernel Image ... OK
## Loading RAMDisk Image at 06000000 ...
Image Name: OXE_NGP_6.16_INT
Image Type: PowerPC Linux RAMDisk Image (gzip compressed)
Data Size: 10727746 Bytes = 10.2 MB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Booting using the fdt at 0x5800000
Loading Ramdisk to 0f564000, end 0ff9f142 ... OK
Loading Device Tree to 007fd000, end 007fefff ... OK
setup_arch: bootmem
ale8377_intip3_setup_arch()
arch: exit

Using Alcatel-Lucent 8377 INTIP3 machine description
Linux version 2.6.23.17-020.001 (alize100@frillux) (gcc version 4.1.2) #1 PREEMPT Wed Oct 30 12:21:52 CET 2013
Found initrd at 0xcf564000:0xcff9f142
[MTD] Found 5 partitions in device-tree
Found MPC83xx PCI host bridge at 0x00000000e0008500. Firmware bus number: 0->0
Zone PFN ranges:
DMA 0 -> 65536
Normal 65536 -> 65536
HighMem 65536 -> 65536
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
0: 0 -> 65536
Built 1 zonelists in Zone order. Total pages: 65024
Kernel command line: root=/dev/ram console=ttyS0,9600 powersave=off boot_from=flash console_baudrate=9600 factory_mode=no
IPIC (128 IRQ sources) at fcff9700
PID hash table entries: 1024 (order: 10, 4096 bytes)
I-pipe 2.0-09: pipeline enabled.
console [kgdb0] enabled
Console: colour dummy device 80x25
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 244352k/262144k available (3988k kernel code, 17496k reserved, 160k data, 535k bss, 156k init)
Mount-cache hash table entries: 512
NET: Registered protocol family 16
Found MPC8377 (hardware revision 2.1)
Read ALE devices configuration from DeviceTree
NULL bootp pointer
PCI: Probing PCI hardware
Generic PHY: Registered new driver
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
NET: Registered protocol family 2
IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
TCP established hash table entries: 8192 (order: 4, 65536 bytes)
TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
TCP reno registered
checking if image is initramfs... it is
Freeing initrd memory: 10476k freed
prom_parse: Bad cell count for /soc@e0000000/mdio@24520/ethernet-phy@1
prom_parse: Bad cell count for /soc@e0000000/mdio@24520/ethernet-phy@2
Xenomai: system heap size: 16384 kB
I-pipe: Domain Xenomai registered.
Xenomai: hal/powerpc started.
Xenomai: init success
I-pipe: Domain IShield registered.
Xenomai: real-time nucleus v2.4.5 (Overdriver) loaded.
Xenomai: starting native API services.
Xenomai: starting POSIX services.
Xenomai: starting RTDM services.
Xenomai: starting RTAI emulator.
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
serial8250.0: ttyS0 at MMIO 0xe0004500 mem 0xd1002500 (irq = 20) is a 16550A
console [ttyS0] enabled
serial8250.0: ttyS1 at MMIO 0xe0004600 mem 0xd1004600 (irq = 21) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize
Gianfar MII Bus: probed
eth0: Gianfar Ethernet Controller Version 1.3-skbr, 00:80:9f:8d:b1:82
GFAR: SKB Handler initialized at CPU#0(max=32)
eth0: MTU = 1500 (frame size=1526, truesize=1808)
eth0: Running with NAPI disabled
eth0: 1024/256 RX/TX BD ring size
eth1: Gianfar Ethernet Controller Version 1.3-skbr, 00:80:9f:8d:b1:83
GFAR: SKB Handler initialized at CPU#0(max=32)
eth1: MTU = 1500 (frame size=1526, truesize=1808)
eth1: Running with NAPI disabled
eth1: 1024/256 RX/TX BD ring size
kgdboe: couldn't parse config at not_configured!
kgdboe: configuration incorrect - kgdboe not loaded.
Usage: kgdboe=[src-port]@[src-ip]/[dev],[tgt-port]@/
physmap platform flash device: 00200000 at ff800000
physmap-flash.0: Found 1 x16 devices at 0x0 in 8-bit bank
Amd/Fujitsu Extended Query Table at 0x0040
number of CFI chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
cmdlinepart partition parsing not available
RedBoot partition parsing not available
Using physmap partition information
Creating 4 MTD partitions on "physmap-flash.0":
0x00000000-0x000e0000 : "firmware"
0x000e0000-0x00100000 : "hardware"
0x00110000-0x001f0000 : "fs"
0x001f0000-0x00200000 : "factory"
fsl-ehci fsl-ehci.0: Freescale On-Chip EHCI Host Controller
fsl-ehci fsl-ehci.0: new USB bus registered, assigned bus number 1
fsl-ehci fsl-ehci.0: irq 38, io base 0xe0023000
fsl-ehci fsl-ehci.0: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
mice: PS/2 mouse device common for all mice
i2c /dev entries driver
esdhc: Freescale Enhanced Secure Digital Host Controller driver
esdhc:slot0: SDCard is Full-Speed Capable (25 MHz)
esdhc:slot0: Invalid maximum block size, assuming 512
mmc0: ESDHC at 0xe002e000 irq 42 DMA
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
IPv6 over IPv4 tunneling driver
sit0: Disabled Privacy Extensions
NET: Registered protocol family 17
drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
Freeing unused kernel memory: 156k init
esdhc:slot0: clock 400000 Hz
esdhc:slot0: SDCard clock is now running at 1302083 Hz
get_cd (or) get_cd(host) is there...
esdhc:slot0: clock 25000000 Hz
esdhc:slot0: SDCard clock is now running at 23809523 Hz
mmc0: new SD card at address b368
mmcblk0: mmc0:b368 STEC 249856KiB
mmcblk0: p1
loop: module loaded
Thu Jan 1 00:00:11 UTC 1970
[Script /etc/rc.d/rc.sysinit (PID=901) started by "init"]
[starti802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
ng cron]
crond[All bugs added by David S. Miller <davem@redhat.com>
1346]: crond: crond (busybox 1.20.2) started, loEthernet Channel Bonding Driver: v3.1.3 (June 13, 2007)
g level 8
[Setbonding: MII link monitoring set to 200 ms
ting kernel/network/platform optADDRCONF(NETDEV_UP): bond0: link is not ready
ions]
[insertinbonding: bond0: Warning: failed to get speed and duplex from eth0, assumed to be 100Mb/sec and Full.
g kernel modulesbonding: bond0: making interface eth0 the new active one.
]
inserting 802bonding: bond0: first active interface up!
1q ()
insertingbonding: bond0: enslaving eth0 as an active interface with an up link.
bonding (mode=1ADDRCONF(NETDEV_CHANGE): bond0: link becomes ready

bonding: bond0: Warning: failed to get speed and duplex from eth1, assumed to be 100Mb/sec and Full.
bonding: bond0: enslaving eth1 as a backup interface with an up link.
inserting x_tables ()
inserting ipt_ttl ()
inserting ipt_TTL ()
inserting ip_tables ip_tables: © 2000-2006 Netfilter Core Team
()
inserting xt_NFLOG ()
inserting xt_NFQUEUE ()
insertiNetfilter messages via NETLINK v0.30.
ng nfnetlink ()
inserting nfnetlink_queue ()
inserting nfnetlink_log ()
inserting iptable_filter ()
inserting iptable_mangle ()
inserting iptable_raw ()
inserting xt_tcputun: Universal TUN/TAP device driver, 1.6
dp ()
insertingtun: © 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
xt_mark ()
insbonding: bond0: link status definitely down for interface eth0, disabling it
bonding: bond0: making interface eth1 the new active one.
erting xt_MARK ()
inserting tun ()
inserting alz-driver ()
Register platform Alcatel-Lucent 8377 INTIP3 specific functions
Invalid magic in bootp request
[wdt] Driver Initialization
cCPU Watchdog Timer not enabled (60 seconds, nowayout=0) tdelay=1000
bonding: bond0: link status definitely down for interface eth1, disabling it
bonding: bond0: now running without any active interface !
rtc model m41t11
m41t11 0-0068: rtc core: registered m41t11 as rtc0
[alz] Register alz_gpio...
[alz] Register Armada EEPROM drivers
Registered led device: CPUgreen
Registered led device: CPUred
Registered led device: CPUyellow
Registered led device: BSYyellow
[Restore system m41t11 0-0068: read: 33 31 d5 05 29 07 21
m41t11 0-0068: read secs=33, mins=31, hours=15, mday=29, mon=6, year=121, wday=4

Thu Jul 29 15:31:33 UTC 2021
[starting background processes]
[starting syslogd]
[Lock reset management to kernel module]
[start loopback device]
[starting network]
[Check Storage device]
[Check SDcard partition]
[Try to mount SDkjournald starting. Commit interval 5 seconds
EXT3 FS on mmcblk0p1,
internal journal
EXT3-fs: mounted filesystem with ordered data mode.
[SDcard partition OK]
[BOOT directory to be upd ated]
End of platform init
Thu Jul 29 15:31:34 UTC 2021
[Script /etc/rc.d/rc (PID=1511) started by "init"]
[Wait for 5m before rotating log to keep header]
=== BIENVENUE TO INTIP 3 Software v. 06.17 in INTIP3 board / intip3 mode / INTIPA role ===
=== Kernel version : 2.6.23.17-020.001 ===
***** SDcard owner = intip3 ***** Board = intip3 *****
[NO IPMG configuration for INTIPA role board]
No password file found - using default password list
PHY: e0024520:02 - Link is Up - 1000/Full
bonding: bond0: link status definitely up for interface eth1.
bonding: bond0: making interface eth1 the new active one.
bonding: bond0: first active interface up!
/etc/config/local/ipmg.cfg: OK
The ipmg.cfg is in good shape in RAM
Starting /etc/rc.d/rcS/01pipe

Starting /etc/rc.d/rcS/10network

Setting hostname....
[Start mod_incid
INCIDENT_DEVICE :: INCIDENT driver registered to Linux
.ko]
IPv4 packet forwarding is enabled....
IPv4 automatic defragmentation is disabled....
IPv4 TCP timestamps is disabled....
Starting /etc/rc.d/rcS/90init
Uboot updater is now working ... getting current version information
Check if we need to update with Uboot bootl100/000.018 ...
Current version : bootl100/000.018 / Recorded version : bootl100/000.018
..... Uboot update not needed .....
[Warning] Net status : yes at 1000Mb/s
start of load appli modules phase
Loading modules - please wait ...
[Start RT2LxCMD]
[Start xeno_bkRegistering Adeos/Xenomai Backtrace
t.ko]
[xeno_bkt]: Albator pid is 1478
[Start xeno_ipmgxeno_ipmg_drv: module license 'Alcatel-Lucent' taints kernel.
_drv.ko]
ipmg_drv module loaded
/proc/IPMG proc entry created
[Start inox_hpi.ko & inox_pci.ko common interfacInox0 Inox_pci found 0 Dsps
e]
Inox1 Inox_pci found 2 Dsps
[Start dbg_mngr.ko and fw_mngr.ko telecom DSPs lModule rt_printf loaded
ow level managemStarting monitor using pipe 1
ent]
[Start xenUUo_printf.ko]
[Start xeno_monitor.ko]
binamcvb642x AUTHENTICATION OK
[Start amcvd.ko common interface]
nbInox:2 dspInfos.InoxId:1 dspInfos.Pos:0 inoxTelId:0 => dspId:0
nbInox:2 dspInfos.InoxId:1 dspInfos.Pos:1 inoxTelId:0 => dspId:1
DSPWare Version : AMCVB / 3.06 / Checksum 1429ba03
[Start adiat_driCreate /proc/adiat
ver.ko common inAdiat driver module loaded
terface]
[Start xeno_mem_/proc/IPMG/DMAMemoryManager proc entry created
mgr.ko]
rt_mem_mgr : General Heap for Real Time : 16777216 bytes
DMA memory allcator initialized : 20 chunks of 131072 bytes
Real-Time Linux Dynamic Memory Manager
[Start xeno_syscxeno_syscall : module loaded.
all.ko]
[Start xeno_syscall_agent]
[Start xeno_ca_kernel.ko]
Application specification : intip3
kernel trace levels : 0
Alcatel-Lucent kernel module loading...

---------------- Rings Init : Begin ---------------
ca_kernel : Creating Heap Tx [ OK ]
ca_kernel : Allocating Heap Tx [512] [ OK ]
ca_kernel : Creating Heap Rx [ OK ]
ca_kernel : Allocating Heap Rx [512] [ OK ]

---------------- Rings Init : End -----------------

fastsk : Shared heap allocated
Module Kernel Loaded
[Start Socket Agent]
[Start c1nv_mngt.ko]
pci_get_device cffe9000
pci_enable_device 0
pci_request_region 2 0
ioremap 2 d3a00000
pci_request_region 1 0
ioremap 1 d3a80000
pci_request_region 0 0
ioremap 0 fcffe400
[PowerOff] (IRQ #0 (0) received).
irq = 18
request_firmware BNVINTIP 0 d22f3fd8
request_firmware TONES 0 d22f4128
[Start intip_mngt.ko]
SoftMSM_Sig = 0
Thu Jul 29 15:31:52 UTC 2021
[Script /etc/rc.shutdown (PID=1763) started by "init"]
Script Log disabled

[Notify RT application to engage shutdown]
ca_kernel : Fast Socket Initialization.
ca_kernel : no param_8021q=-1 is used
ca_kernel : no vlan se t

C1drvDownloadBinary
C1drvDownloadBinary 0x0
C1drvIrqRequest
idx_hist ff
idx_hist 0
C1drvIrqEnable
C1drvRemoveReset
start ok
Module INTIP Loaded
Directory /mnt/flash/info/c1nv OK
/mnt/flash/info/c1nv/c1nvnorst doesn't exist -1
Next idx_hist: 1
Updated histc1nv in flash
[Start c1nv_proc.ko]
[Start srtp_module.ko]
SRTP Module is loaded but security is not implemented in this release
[Start ca_media_server.ko]
[Notify RT application to halt now]
[Backup system tm41t11 0-0068: write secs=56, mins=31, hours=15, mday=29, mon=6, year=121, wday=4
ime to RTC]
m41t11 0-0068: write 56 31 d5 05 29 07 21
Thu Jul 29 15:31:56 UTC 2021
[Script /etc/rc.d/init.d/save_info (PID=1786) started by "/etc/rc.shutdown"]
[No backtrace]
[No new core dump]
[Saving logs]
[Stopping swap]
[Lazy Unmounting everything]
media Module is loading (setcomphs=0)...
media Module version Jul 20 2015-19:25:57
media Module Author Written by ALE ...
Starting Load of media server module
End of update_obj_tb phase
End of determine_offset phase : 9 objects passed
Start of allocators construction phase (static)
init module media_server : after allocation of VoIP context objects pools
End of loop on channels from 0 to 128
Before special objects treatment : RTCP RR and fastsk for RTCP and T38 objects
End of link on fastsk objects for RTCP_RR : inst numbers from 128 to 255
End of link on fastsk objects for RTCP_SR : inst numbers from 256 to 383
End of link on fastsk objects for udptl : inst numbers from 384 to 511
fastsk objects srtp for Thales box : inst number 512
fastsk objects fax for Thales box : inst number 513
Module media_server loaded
media server module is loaded
[Stopping network]
[End of rc.shutdown]
The system is going down NOW!
Sent SIGTERM to all processes
SyscallAgent[1732]: Signal 15 catched --> shutdown!!!

SyscallAgent[1732]: rt_syscall0 closed

Sent SIGKILL to all processes
Requesting system reboot
Restarting system.
Ъ
29.07.2021 11:41:57, santeri.