Resetting the board.э

U-Boot 1.3.0-rc3 (Jan 12 2012 - 14:42:54) 3EH30350AAAS bootl100/000.018

Reset Status: Software Hard, External/Internal Soft, External/Internal Hard

CPU:   e300c4, MPC8377, Rev: 21 at 666.666 MHz, CSB:  333 MHz
I2C:   ready
DRAM:  
   DDR DIMM: data bus width is 64 bit without ECC
   DDRC ECC mode: OFF
   DDR RAM: 256 MB
FPGA: /soc@e0000000/gpio@c00/fpga@01f00000: FPGA4C1NV reloading... done
FLASH:  2 MB
PCI:   Bus Dev VenId DevId Class Int
        00  17  1064  2102  0000  00
        00  18  1064  2102  0000  00
        00  1d  10ee  0300  0b40  ff
In:    serial
Out:   serial
Err:   serial
Net:   TSEC0, TSEC1
eSDHC: 4bit-buswidth mode
SATA:  SATA0 [Link:   no RDY]
       SATA1 [Link:   no RDY]
## Booting image at ff836df0 ...
   Image Name:   aleboot.bin
   Image Type:   PowerPC U-Boot Standalone Program (uncompressed)
   Data Size:    9576 Bytes =  9.4 kB
   Load Address: 00200000
   Entry Point:  00201bd4
   Verifying Checksum ... OK
OK
m41t11 Chip
No Prompt
Press ^B^I to enter into the Bios menu  0 Reloading default boot sequence.
Booting from SDMMC
Hit any key to stop autoboot:  0 
## Booting image at ff839398 ...
   Image Name:   gpioinit.bin
   Image Type:   PowerPC U-Boot Standalone Program (uncompressed)
   Data Size:    2185 Bytes =  2.1 kB
   Load Address: 00200000
   Entry Point:  00200620
   Verifying Checksum ... OK
OK
Watchdog Started

** Unable to read "/boot/u-boot.scr" from mmc 0:1 **
Resetting the board.э

U-Boot 1.3.0-rc3 (Jan 12 2012 - 14:42:54) 3EH30350AAAS bootl100/000.018

Reset Status: Software Hard, External/Internal Soft, External/Internal Hard

CPU:   e300c4, MPC8377, Rev: 21 at 666.666 MHz, CSB:  333 MHz
I2C:   ready
DRAM:  
   DDR DIMM: data bus width is 64 bit without ECC
   DDRC ECC mode: OFF
   DDR RAM: 256 MB
FPGA: /soc@e0000000/gpio@c00/fpga@01f00000: FPGA4C1NV reloading... done
FLASH:  2 MB
PCI:   Bus Dev VenId DevId Class Int
        00  17  1064  2102  0000  00
        00  18  1064  2102  0000  00
        00  1d  10ee  0300  0b40  ff
In:    serial
Out:   serial
Err:   serial
Net:   TSEC0, TSEC1
eSDHC: 4bit-buswidth mode
SATA:  SATA0 [Link:   no RDY]
       SATA1 [Link:   no RDY]
## Booting image at ff836df0 ...
   Image Name:   aleboot.bin
   Image Type:   PowerPC U-Boot Standalone Program (uncompressed)
   Data Size:    9576 Bytes =  9.4 kB
   Load Address: 00200000
   Entry Point:  00201bd4
   Verifying Checksum ... OK
OK
m41t11 Chip
No Prompt
Press ^B^I to enter into the Bios menu  6 


1- Load from Hard disk
2- Load from SDcard
3- Load from Ethernet
4- Load from Hard disk & bootp
5- Load from SDcard & bootp
6- Display MAC addresses , CPUID and Serial Number
7- Reset
Your choice followed by carriage return : 
Time out
Booting from NETWORK BOOTP
 Hit any key to stop autoboot:  0 
## Booting image at ff839398 ...
   Image Name:   gpioinit.bin
   Image Type:   PowerPC U-Boot Standalone Program (uncompressed)
   Data Size:    2185 Bytes =  2.1 kB
   Load Address: 00200000
   Entry Point:  00200620
   Verifying Checksum ... OK
OK
Watchdog Started
Speed: 1000, full duplex

Using TSEC0 device 
BOOTP broadcast request 1 in progress ---> 00:80:9f:fd:51:af 
Using TSEC0 device
TFTP from server 10.10.10.15; our IP address is 10.10.10.16
Filename '/DHS3bin/downbin/intip3/binintip3start'.
Load address: 0x100000
Loading: #
done
Bytes transferred = 689 (2b1 hex)
## Executing script at 00100000
Speed: 1000, full duplex
Using TSEC0 device
TFTP from server 10.10.10.15; our IP address is 10.10.10.16
Filename '/DHS3bin/downbin/intip3/binintip3linux'.
Load address: 0x4000000
Loading: #################################################################
    #################################################################
    ###########
done
Bytes transferred = 2006429 (1e9d9d hex)
Speed: 1000, full duplex
Using TSEC0 device
TFTP from server 10.10.10.15; our IP address is 10.10.10.16
Filename '/DHS3bin/downbin/intip3/binintip3rdimg'.
Load address: 0x6000000
Loading: #################################################################
    #################################################################
    #################################################################
    #################################################################
    #################################################################
    #################################################################
    #################################################################
    #################################################################
    #################################################################
    #################################################################
    #################################################################
    #################################################################
    #################################################################
    #################################################################
    #######################################################
done
Bytes transferred = 13772396 (d2266c hex)
## Booting image at 04000000 ...
   Image Name:   Linux-2.6.23.17-020.001
   Image Type:   PowerPC Linux Kernel Image (gzip compressed)
   Data Size:    2006365 Bytes =  1.9 MB
   Load Address: 00000000
   Entry Point:  00000000
   Verifying Checksum ... Bad Data CRC
Resetting the board.э